Tuesday, March 30, 2010

Continuous Binding

I am aware of at least a half-dozen variations to attach that last bit of binding to a quilt with a smooth bias seam. Some are easier than others to remember.

I don't remember when I learned to finish the binding so that it appears 'seamless.' But the method I learned has stuck. For some reason, it makes sense to me. I've tried other methods, some of them with fewer steps, some with more, and I always come back to my old stand by.

Here's how it goes.

1. After trimming the batting and backing even with the quilted top, sew the binding 1/4" from the edge of the quilt, leaving about 24" of the binding unsewn, that's at least 12" of 'unattached' binding on each end. Place the unbound section of the quilt flat on your work table. Lay the binding ends evenly along the raw edge of the quilt and fold the binding back on itself so the folds meet and 'kiss.'

2. Make two marks on the top binding layer one half the width of the binding from the fold. In other words, I've cut my binding strips 2-1/4", so one half of that is 1-1/8". I have two lines on the binding, each 1-1/8" away from the fold. Let's say you cut your binding strips 2-1/2" wide, then half of that is 1-1/4" - half of a 3-1/2" binding is 1-3/4" - half of a 4" binding is 2" - works for any binding width.

3. Fold the quilt onto itself, and pin the quilt layers creating some slack allowing you to work with the binding ends easier.

4. Bring the binding end from the left above the quilt onto the work table and open the fold. Place the binding so you can see the marking line, right side up.

5. Open the crease, and fold the right binding end, wrong sides together, at the marking line,

6.  Then place the fold from the right binding aligned with edge of the left binding. At the same time, align the marking on the left binding with edge of the right binding.

7. Open the right binding fold, then draw a line, parallel to the quilt top, from edge to edge as shown. Secure the binding with pins on both sides of the drawn line.

8. Sew on the line.

9. Trim about 1/4" away from sewing (un-pin the quilt to test it first, if you like!)

10. Pin and sew to quilt edge.

11. Seamless!


Whatever method you choose to create a 'seamless' continuous binding, you'll never have a 'lumpy' edge again!

Bound to quilt!
Joan

7 comments:

  1. OMG! Thank you, Joan. I have found the other online binding tutorials difficult to understand. Your method makes sense to me as well, and I am grateful that you published it. I intend to print it out and keep it in my sewing table drawer. With enough applications, forgetting will be a thing of the past. Again, thanks.

    By the way, love the use of the 'love of my life"...Kaffe!!!

    Gail

    ReplyDelete
  2. Hi Joan - I'm sure that this is the most terrific method ever offered! However, it's over my non-quilter's head, LOL. I would love to share this on my blog, if that's OK?

    ReplyDelete
  3. I saw a link on your facebook page and had to try it. It worked great! I have tried Sally Collins' method and it never worked out quite right for me. This method made sense to me and it actually worked out correctly! I plan on using this method for all my bindings. Thank you so much.

    Rosemary Dickinson

    ReplyDelete
  4. That looks a lot easier then the tool i bought which i have never figured out ! I can't wait to try it!!!

    ReplyDelete
  5. I have 'that' tool as well and it's beyond me :o) I'm doing a quilt at the moment so I'll try this method, looks easy enough and great photo's. Thankyou so much, hope your having a great holiday?

    ReplyDelete
  6. I have that tool as well, and have tried it first several times, but only successful once. I think I have a mental block about it. I find myself going back to the tried and true method, which is remarkably, the one you do Joan! Thank you for a great tutorial about it!

    ReplyDelete